wince系统启动问题

为什么的我的系统启动到这里就不动了呢，下面是串口的调试信息：
.............................................................
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30200000h,TOTAL:30408714]
RECEIVED FILE SIZE:30408714 (824KB/S, 36S)
Downloaded file at 0x30000000, size = 30408704 bytes
..
Windows CE Kernel for ARM (Thumb Enabled) Built on Feb  8 2007 at 23:36:51
ProcessorType=0920  Revision=0
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 8c2013bc

Windows CE Firmware Init
INFO: Initializing system interrupts...
INFO: Initializing system clock(s)...
INFO: Initializing driver globals area...
SDMMC config set rGPGCON: fd96ffba
OEMInit Done...
Sp=ffffc7cc
NandFlash FMD_Init
NandFlash FMD_Init Done

我的开发板上没有网卡，其他的和QQ2440的差不多，也是64M FALSH和64M sram

这个是的config.bib文件内容：
MEMORY

;#define CHAIN_ADDRESS    81E40000
;    CHAIN            $(CHAIN_ADDRESS)    00001000    RESERVED
;    pdwXIPLoc        00000000  $(CHAIN_ADDRESS)      FIXUPVAR

;;; Tarzan Debug mode
    NK            8C200000  01D00000  RAMIMAGE        ;change by lyc
;    NK            8C300000  01D00000  RAMIMAGE
;    CHAIN            81E40000  00001000  RESERVED
;    DRIVERS            81E41000  001BF000  RAMIMAGE

;    RESERVE             8df00000  00080000

;    RAM                 8E000000  01F00000  RAM
;
    RAM                 8E000000  01c00000  RAM

; Common RAM areas
    AUD_DMA         8c002000  00002000  RESERVED
    DRV_GLB            8c010000  00010000  RESERVED
    DBGSER_DMA        8c022000  00002000  RESERVED
    SER_DMA            8c024000  00002000  RESERVED
;    IR_DMA            8c026000  00002000  RESERVED
    SD_DMA            8c028000  00008000  RESERVED

;    EDBG            8c030000  00020000  RESERVED    ;change by lyc
;    CAMERA            8c050000  000A0000  RESERVED
;    CAMERA            8c088000  00140000  RESERVED

;    DISPLAY            8c160000  00030000  RESERVED  ;320*240
;    DISPLAY            8c1d0000  00100000  RESERVED
    DISPLAY            8c100000  00100000  RESERVED



CONFIG

    COMPRESSION=ON
    KERNELFIXUPS=ON

IF IMGPROFILER  
    PROFILE=ON
ENDIF

IF IMGPROFILER !
    PROFILE=OFF
ENDIF

;;;;;;;;;;;;;;;;;; add by lyc ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; configur the percentage of RAM allocated for the file system ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
IF IMGTINYFSRAM !        
    FSRAMPERCENT=0x10101010
ENDIF

IF IMGTRUSTROMONLY
    IF IMGNOTALLKMODE
        ROMFLAGS=12
    ENDIF
    IF IMGNOTALLKMODE !
        ROMFLAGS=10
    ENDIF
ENDIF

IF IMGTRUSTROMONLY !
    IF IMGNOTALLKMODE
        ROMFLAGS=2
    ENDIF
    IF IMGNOTALLKMODE !
        ROMFLAGS=0
    ENDIF
ENDIF

    ROMSTART=8C200000   ; change by linyichun
    ROMWIDTH=32
    ROMSIZE=01D00000

这个是我在QQ2440开发板上的启动的完整信息，我截取了后面部分
Windows CE Firmware Init
INFO: Initializing system interrupts...
INFO: Initializing system clock(s)...
INFO: Initializing driver globals area...
SDMMC config set rGPGCON: fd96ffba
OEMInit Done...
Sp=ffffc7cc
NandFlash FMD_Init
NandFlash FMD_Init Done
PWR: Process Attach
>PWR_Init(602ED68)
HW_Init : GetProcAddress
HW_Init : ERROR_INVALID_PARAMETER
HW_Init : InitializeCriticalSection
HW_Init : VirtualAlloc
HW_Init : pPWR->State
HW_Init : HW_InitRegisters
HW_Init : CreateEvent
HW_Init : InterruptInitialize
HW_Init : CreateThread
HW_Init : CeSetThreadPriority
HW_Init OOCS: 0x00
HW_Init INT1: 0x00
HW_Init INT2: 0x00
HW_Init INT3: 0x00
HW_Init : Donw
<PWR_Init:0x37c20
>PWR_Open(0x37c20, 0x0, 0x3)
<PWR_Open:1
>PWR_IOControl(0x321000, 0x0, 0, 0x6037918)
<PWR_IOControl:1
>PWR_Open(0x37c20, 0x0, 0x3)
<PWR_Open:2
PWR_Close(0x37c20)
384 clock
+CS8900:DriverEntry
USB:OhcdPdd_Init
++InitializeOHCI
USB:*pIrq=11, *pioPortBase=0x3F0000
OHCD: MapIrq2SysIntr(11): 27
OHCD: Memory Object
--InitializeOHCI
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\AFD). Driver cannot be unloaded.
USB enable interrutp
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\PPP). Driver cannot be unloaded.
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\TELNETD). Driver cannot be unloaded.
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions at (Drivers\BuiltIn\SDBusDriver). Driver cannot be unloaded.
    charlie::SDIO::SDHOST::SDCSDCardDllEntry::DLL_PROCESS_ATTACH
    charlie::SDIO::SDCInitialize+
    charlie::SDIO::SDCInitialize-
--S3C2440DISP::InitializeHardware
Lyg.p: Layout Manager successfully initialized to  2
Touch Init
Maximum Allowed Error 7:
MSIM: IM_ReadRegistry read KB 5
Explorer(V2.0) taskbar thread started.
NDISPWR:: Found adapter [CS89001]
RasEntry '`USB Socket Default' Created

应该是flash驱动引起的，你修改了什么地方？

是不是加了保存注册表功能？

to :qlb211999
我是加了注册表保存功能,但是没有更改flash的驱动,谢谢
顺便问一下,PWR: Process Attach
>PWR_Init(602ED68)
HW_Init : GetProcAddress
这些信息都在那些文件和函数中输出的，我怎么也找不到,我的wince5.0

在BSP的powerbutton驱动里输出的