高分求winnt下的inf文件移植到2k

现在本人有一个winnt4.0下用的中间层驱动程序，现在想把它放到2000下运行，但安装硬件时显示没有对应硬件信息，不知各位大鸟有谁做过相类似的工作，指定一二，inf文件如下：
[Source Media Descriptions]
    1  = \"StackMAC setup\"  , TAGFILE = disk1
;
[Identify]
   set OptionType = NetService
   set Status     = STATUS_SUCCESSFUL
   set Media      = #(\"Source Media Descriptions\",1,1)
   Return $(Status) $(OptionType) $(Media)
;
[Options]
    STACKMAC
;
[FileConstants]
UtilityInf      = \"UTILITY.INF\"
subroutineinf   = \"SUBROUTN.INF\"
SoftwareType    = \"service\"
Exit_Code       = 0
NetEventDLL     = \"%SystemRoot%\\System32\\netevent.dll\"
Manufacturer    = \"Nokia Telecommunications Oy\"
ProductMajorVersion     = \"4\"
ProductMinorVersion     = \"0\"
ProductVersion  = $(ProductMajorVersion)\".\"$(ProductMinorVersion)
ProductSoftwareName     = \"StackMAC\"
ProductSoftwareImagePath = \"\\SystemRoot\\System32\\drivers\\skmn.sys\"

NetRuleSoftwareType     = \"StackMAC lmNetService ndisTransport\"
NetRuleSoftwareClass    = {\"rasCapableTransport netBiosTransport\"}

NetRuleSoftwareUse      = $(SoftwareType)\" yes yes\"
NetRuleSoftwareBindForm = \"\"\"StackMAC\"\" yes yes simple\"

ProductKeyName  = $(!NTN_SoftwareBase)\"\\\"$(Manufacturer)\"\\\"$(ProductSoftwareName)\"\\CurrentVersion\"
ParamKeyName    = $(!NTN_ServiceBase)\"\\\"$(ProductSoftwareName)\"\\Parameters\"
TargetKeyName  = $(!NTN_SoftwareBase)\"\\\"$(Manufacturer)\"\\Installation\"
[GeneralConstants]
from      = \"\"
to        = \"\"
ExitCodeOk     = 0
ExitCodeCancel = 1
ExitCodeFatal  = 2
KeyNull         = \"\"
MAXIMUM_ALLOWED   = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct      = \"\"
KeyParameters   = \"\"
TRUE            = 1
FALSE           = 0
NoTitle            = 0
ExitState   = \"Active\"
OldVersionExisted = $(FALSE)
DriverPath      = $(!STF_NTPATH)\\drivers
[date]
    Now = {} ? $(!LIBHANDLE) GetSystemDate
[Identify]
    read-syms Identification
    set Status     = STATUS_SUCCESSFUL
    set Identifier = $(OptionType)
    set Media      = #(\"Source Media Descriptions\", 1, 1)
    Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
    set Status        = STATUS_FAILED
    set OptionList     = {}
    set OptionTextList = {}
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) in $(LanguageList)
        goto returnoptions
    else
        set Status = STATUS_NOLANGUAGE
        goto finish_ReturnOptions
    endif
returnoptions = +
    set OptionList     = ^(Options, 1)
    set OptionTextList = ^(OptionsText$($0), 1)
    set Status         = STATUS_SUCCESSFUL
finish_ReturnOptions = +
    Return $(Status) $(OptionList) $(OptionTextList)
;
[InstallOption]
    set Option   = $($1)
    set SrcDir   = $($2)
    set AddCopy  = $($3)
    set DoCopy   = $($4)
    set DoConfig = $($5)
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) NOT-IN $(LanguageList)
        Return STATUS_NOLANGUAGE
    endif
    Debug-Output \"OEMNXPNB.INF: STF_CWDDIR is: \"$(!STF_CWDDIR)
    Debug-Output \"OEMNXPNB.INF: STF_LANGUAGE is: \"$(!STF_LANGUAGE)
    set-subst LF = \"\\n\"
    read-syms GeneralConstants
    read-syms FileConstants
    read-syms DialogConstants$(!STF_LANGUAGE)
    ifstr(i) $(!NTN_Origination) == \"NCPA\"
        set Continue = $(OK)
    endif
    read-syms FileConstants$(!STF_LANGUAGE)
    detect date
    set-title  $(FunctionTitle)
    set to   = Begin
    set from = Begin
    set CommonStatus = STATUS_SUCCESSFUL
    EndWait
Begin = +
    Ifstr(i) $(!NTN_InstallMode) == deinstall
        set StartLabel = removeadapter
    else-Ifstr(i) $(!NTN_InstallMode) == Update
        set StartLabel = UpgradeSoftware
    else-Ifstr(i) $(!NTN_InstallMode) == bind
        set StartLabel = bindingadapter
    else-Ifstr(i) $(!NTN_InstallMode) == configure
        OpenRegKey $(!REG_H_CLASSES) \"\" $(TargetKeyName) $(!REG_KEY_QUERY_VALUE) KeyTarget
        Ifstr $(KeyTarget) != $(KeyNull)
            GetRegValue $(KeyTarget),\"TargetDirectory\", NokiaSysDirValue
            CloseRegKey $(KeyTarget)
            NokiaSysDir = *($(NokiaSysDirValue),4)\\system32
        endif
        ifstr $(NokiaSysDir) == \"\"
            set NokiaSysDir = c:\\nokiamgr\\system32
        endif
        RunProgram ExitCode \"StackMAC setup\" \"\" $(NokiaSysDir)\\pcq3.exe
        goto end
    else
        set StartLabel = installadapter
    endif
    set RadioDefault = 2
    set RadioIn = {$(RadioDefault)}
    set from = $(fatal)
    set to = $(fatal)
    goto $(StartLabel)
installadapter = +
    OpenRegKey $(!REG_H_LOCAL) \"\" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
    Ifstr $(KeyProduct) != $(KeyNull)
        CloseRegKey $(KeyProduct)
        Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
            $(ProductVersion)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output \"ShellCode error: cannot get an error string.\"
            goto ShellCodeError
        endif
        goto end
    endif
    CloseRegKey $(KeyProduct)
    goto installproduct
installproduct = +
    StartWait
    ifint $(OldVersionExisted) == $(FALSE)
        Ifstr(i) $(DoCopy) == \"YES\"
           Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
           Ifint $($ShellCode) != $(!SHELL_CODE_OK)
               Goto ShellCodeError
           Else-Ifstr(i) $($R0) == STATUS_FAILED
               Shell $(UtilityInf) RegistryErrorString \"ASK_SOURCE_FAIL\"
               ifint $($ShellCode) != $(!SHELL_CODE_OK)
                   goto ShellCodeError
               endif
               set Error = $($R0)
               Goto fatal
           Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
               Goto successful
           Endif
           Set SrcDir = $($R1)
        Endif
        install \"Install-Option\"
        ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
           Shell $(UtilityInf) RegistryErrorString \"UNABLE_COPY_FILE\"
           ifint $($ShellCode) != $(!SHELL_CODE_OK)
               goto ShellCodeError
           endif
           set Error = $($R0)
           goto fatal
        endif
        set OEM_ABANDON_ON = TRUE
        Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
   $(ProductSoftwareName), +
   $(ProductSoftwareName), +
   $(ProductSoftwareDisplayName), $(STF_CONTEXTINFNAME), +
   $(ProductSoftwareImagePath), \"kernel\", \"TDI\", {}, \"\",+
   $(NetEventDLL)
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) !=  NO_ERROR
   EndWait
   CloseRegKey $($R1)
   CloseRegKey $($R2)
   CloseRegKey $($R3)
   CloseRegKey $($R4)
   CloseRegKey $($R5)
   goto fatalRegistry
endif
Set SoftProductKey      = $($R1)
Set SoftNetRuleKey      = $($R2)
Set SoftServiceKey      = $($R3)
set KeyParameters       = $($R4)
Set SoftLinkageKey      = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
  {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
  {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
  {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
  {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
  {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
  {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell  $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
set RegistryErrorIndex = $($R0)
Ifstr $(RegistryErrorIndex) != NO_ERROR
   CloseRegKey $(SoftProductKey)
   CloseRegKey $(SoftNetRuleKey)
   CloseRegKey $(SoftServiceKey)
   CloseRegKey $(SoftLinkageKey)
   CloseRegKey $(KeyParameters)
   goto fatalRegistry
endif
set NewValueList = {{type    ,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)}, +
   {use     ,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
   {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
   {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell  $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
set RegistryErrorIndex = $($R0)
Ifstr $(RegistryErrorIndex) != NO_ERROR
   CloseRegKey $(SoftProductKey)
   CloseRegKey $(SoftNetRuleKey)
   CloseRegKey $(SoftServiceKey)
   CloseRegKey $(SoftLinkageKey)
   CloseRegKey $(KeyParameters)
   goto fatalRegistry
endif
Set NewValueList = {{NbProvider,$(NoTitle),$(!REG_VT_SZ),\"_nb\"}}
Shell  $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
Ifstr $(RegistryErrorIndex) != NO_ERROR
   CloseRegKey $(SoftProductKey)
   CloseRegKey $(SoftNetRuleKey)
   CloseRegKey $(SoftServiceKey)
   CloseRegKey $(SoftLinkageKey)
   goto fatalRegistry
endif
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftLinkageKey)
    endif
    goto writeparameters
writeparameters = +
    CloseRegKey $(KeyParameters)
    EndWait
    goto successful
bindingadapter =+
    set Error = \"Binding: Sorry, not yet implemented.\"
    goto fatal
removeadapter = +
    Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output \"ShellCode error\"
goto ShellCodeError
    endif
    set RegistryErrorIndex = $($R0)
    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
    endif
    goto end
UpgradeSoftware = +
    ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
OpenRegKey $(!REG_H_LOCAL) \"\" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
   GetRegValue $(KeyProduct),\"MajorVersion\", VersionInfo
   set Version = *($(VersionInfo), 4)
   Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
   ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output \"ShellCode error\"
goto ShellCodeError
   endif
   set !UG_Filename = $($R0)
   ifstr(i) $(!UG_Filename) != \"\"
install \"Install-Update\"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
   goto fatal
endif
   endif
   SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
   SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
   ifint $(Version) != $(ProductVersion)
   endif
   CloseRegKey $(KeyProduct)
else
   goto fatalregistry
endif
    endif
    goto end
successful = +
    goto end
warning = +
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), \"WARNING\", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
    endif
    ifstr(i) $($R1) == \"OK\"
goto $(to)
    else-ifstr(i) $($R1) == \"CANCEL\"
goto $(from)
    else
goto \"end\"
    endif
nonfatalinfo = +
    Set CommonStatus = STATUS_USERCANCEL
    Set Severity = STATUS
    goto nonfatalmsg
nonfatal = +
    Set Severity = NONFATAL
    goto nonfatalmsg
nonfatalmsg = +
    ifstr(i) $(Error) == \"\"
Shell $(UtilityInf) RegistryErrorString \"SETUP_FAIL\"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
   goto ShellCodeError
endif
set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
    endif
    ifstr(i) $($R1) == \"OK\"
goto $(from)
    else
goto \"end\"
    endif
fatalregistry = +
    Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
    endif
    set Error = $($R0)
    goto fatal
fatal = +
    ifstr(i) $(Error) == \"\"
Shell $(UtilityInf) RegistryErrorString \"SETUP_FAIL\"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
   goto ShellCodeError
endif
set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), \"FATAL\", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
    endif
    goto setfailed
ShellCodeError = +
    set DlgType      = \"MessageBox\"
    set STF_MB_TITLE = $(ShellCodeErrorTitle)
    set STF_MB_TEXT  = $(ShellCodeErrorText)
    set STF_MB_TYPE  = 1
    set STF_MB_ICON  = 3
    set STF_MB_DEF   = 1
    ui start \"Error Message\"
    goto setfailed
setfailed = +
    set CommonStatus = STATUS_FAILED
    ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto removeadapter
    endif
    goto end
end = +
    goto term
term = +
    Return $(CommonStatus)
[Install-Option]
    set STF_VITAL = \"\"
    ifstr(i) $(AddCopy) == \"YES\"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\\drivers
AddSectionFilesToCopyList Files-App $(SrcDir) $(!STF_WINDOWSSYSPATH)
    endif
    ifstr(i) $(DoCopy) == \"YES\"
       set !STF_NCPA_FLUSH_COPYLIST = TRUE
       CopyFilesInCopyList
    endif
    ifstr(i) $(DoConfig) == \"YES\"
    endif
    Exit
[Install-Update]
   set STF_VITAL        = \"\"
   set STF_OVERWRITE    = \"VERIFYSOURCEOLDER\"
   AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\\drivers
   AddSectionFilesToCopyList Files-App $(SrcDir) $(!STF_WINDOWSSYSPATH)
   AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList
   Exit
[ProductType]
STF_PRODUCT  = Winnt
STF_PLATFORM = I386
[Files-Inf]
1,      oemsetup.inf,    SIZE=1000,     RENAME=$(!UG_Filename)
[Files-StackMAC]
1,SKMN.SYS , SIZE=999
[Files-App]
[LanguagesSupported]
    ENG
[OptionsTextENG]
    STACKMAC = \"StackMAC\"
[FileConstantsENG]
ProCaption   = \"Windows NT Setup\"
ProCancel    = \"Cancel\"
ProCancelMsg = \"Windows NT Networking is not correctly installed.  \"+
      \"Are you sure you want to cancel copying files?\"
ProCancelCap = \"Network Setup Message\"
ProText1     = \"Copying:\"
ProText2     = \"To:\"
FunctionTitle   = \"StackMAC Driver\"
ProductSoftwareDescription      = \"StackMAC Driver\"
ProductSoftwareDisplayName = \"StackMAC Driver\"
ProductSoftwareTitle    = \"StackMAC Driver\"
ShellCodeErrorTitle     = \"Error: \"$(FunctionTitle)
ShellCodeErrorText      = \"Shell Code Error.\"
[DialogConstantsENG]
Help        = \"&Help\"
Exit        = \"Cancel\"
OK          = \"OK\"
HelpContext = \"\"
Continue    = \"Continue\"
Cancel      = \"Cancel\"
[FileDependentDlgENG]
GroupLabel = \"Optimization:\"
Radio1 = \"&Minimize Memory Used\"
Radio2 = \"&Balance\"
Radio3 = \"M&aximize Throughput && Connections\"
DlgType = \"Radio\"              
DlgTemplate = \"NBF\"            
Caption = $(FunctionTitle)
OptionsGreyed = {}
HelpContext = $(!IDH_DB_OEMNXPNB_INS)