|
2680楼#
发布于：2005-03-29 09:29
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7 |
|
|
2681楼#
发布于：2005-03-29 09:30
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7 |
|
|
2682楼#
发布于：2005-03-29 09:31
a valid address is an address within any
sector selected for erasure. During chip erase, a valid address is any non-protected sector address. :D :D :o :D :mad: :o :o :o |
|
|
2683楼#
发布于：2005-03-29 09:32
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during ;) :cool: :o :mad: |
|
|
2684楼#
发布于：2005-03-29 09:32
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7 |
|
|
2685楼#
发布于：2005-03-29 09:33
Table 10 shows the outputs for Toggle Bit I on DQ6.
Figure 6 shows the toggle bit algorithm in flowchart form, and the section :D |
|
|
2686楼#
发布于：2005-03-29 09:33
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during ;) :cool: :o :mad: :D |
|
|
2687楼#
发布于：2005-03-29 09:33
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7 |
|
|
2688楼#
发布于：2005-03-29 09:35
Table 10 shows the outputs for Toggle Bit I on DQ6.
Figure 6 shows the toggle bit algorithm in flowchart form, and the section :D :mad: |
|
|
2689楼#
发布于：2005-03-29 09:36
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7 |
|
|
2690楼#
发布于：2005-03-29 09:36
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during ;) :cool: :o :mad: :D :D :cool: |
|
|
2691楼#
发布于：2005-03-29 09:37
After an erase command sequence is written, if all
sectors selected for erasing are protected, :) :) :mad: :D :mad: |
|
|
2692楼#
发布于：2005-03-29 09:38
After an erase command sequence is written, if all
sectors selected for erasing are protected, :o :cool: :D |
|
|
2693楼#
发布于：2005-03-29 09:38
Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. :mad: :D :mad: |
|
|
2694楼#
发布于：2005-03-29 09:39
When the Embedded Erase
algorithm is complete, or if the device enters the Erase Suspend mode, :mad: :mad: :mad: |
|
|
2695楼#
发布于：2005-03-29 09:39
After an erase command sequence is written, if all
sectors selected for erasing are protected, :o :cool: :D :D :o |
|
|
2696楼#
发布于：2005-03-29 09:41
Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. :mad: :D :mad: :D |
|
|
2697楼#
发布于：2005-03-29 09:41
Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. :mad: :mad: |
|
|
2698楼#
发布于：2005-03-29 09:42
When the Embedded Erase
algorithm is complete, or if the device enters the Erase Suspend mode, :o :o :mad: :o :D :mad: |
|
|
2699楼#
发布于：2005-03-29 09:44
a valid address is an address within any
sector selected for erasure. During chip erase, a valid address is any non-protected sector address. :D :D |
|