WINCE无法启动

Writing to flash at Address= 0x60000000, Length = 0xDCCD28
................................................................................
..............................Found pTOC signature.
ROMHDR at Address 60000044h
RomHdr.ulRAMStart=E9300C12h RomHdr.physfirst=E9300C12h.
Got EDBG_CMD_JUMPIMG
Got EDBG_CMD_CONFIG, flags:0x00000000
EBOOT: pCfgData = 0x64472, pCfgData->Flags
INFO: Jumping to image at 0x60001006...
Windows CE Kernel for ARM (Thumb Enabled) Built on Jun 24 2004 at 18:25:00
ProcessorType=0920  Revision=0
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 88001150
InitClock...
Processor = 199Mhz, Bus = 99Mhz
Sp=ffffc7cc
INFO: FMD_Init.
INFO: InitializeFlash.
终端到这里就不动了？？ 是哪里设置的问题还是 ？？

 

到INFO: InitializeFlash.停了，那估计就是Flash驱动有问题了。

可能是FLASH驱动有问题,把NK给破坏了,
看看OS与FLASH驱动用的硬件空间是不是重叠了.

谢谢两位大虾的提示
我没改过FLASH相关的代码，BIB文件的培植是这样的，应该没重叠：
RAM          80200000        01E00000        RAM
    NK          88000000        00f00000        RAMIMAGE
我检查了下SETTING中把IMGFLASH 和BSP_EP93XX_COPY_FLASH_TO_RAM都设置了1，现在我把BSP_EP93XX_COPY_FLASH_TO_RAM=1 给remove了。编译后出现了这样的错误：BUILD: [Thrd:Sequence:Type  ] Message
BUILD: [01:0000005214:ERRORE] c:\WINCE500\PUBLIC\COMMON\OAK\DRIVERS\DISPLAY\EMULROTATE\ebdinv08.cpp(0) : fatal error C1033: cannot open program database 'c:\wince500\public\common\oak\lib\armv4i\retail\emulrotate.pdb'

BUILD: [01:0000005233:ERRORE] c:\WINCE500\PUBLIC\COMMON\OAK\DRIVERS\DISPLAY\EMULROTATE\ebcp0408.cpp(0) : fatal error C1033: cannot open program database 'c:\wince500\public\common\oak\lib\armv4i\retail\emulrotate.pdb'

BUILD: [01:0000005275:ERRORE] LINK : fatal error LNK1181: cannot open input file 'obj\ARMV4I\retail\ebdinv08.obj'

C:\WINCE500\build.log(1) : error SYSGEN0000: error(s) in sysgen phase
这样的错误以前也出现过，一旦出现好象就只有重装系统了。因为每次重新编译cannot open program database 的提示内容不一样。很郁闷，昨天一夜没睡好。

重装了下系统,编译是正常了!下载完后到这里就停止了!
Using device name: EDB9315A65518
Device EDB9315A65518, IP 192.168.1.103, Port 981
Calling EdbgInitDHCP
-InitEther
-OEMKitlInit

!Kitl buffer specified by OAL is not required, ignore...
Host connected
Host IP: 192.168.1.115, port 1380
KITLGlobalState == 0x61
KITL Initialized
请帮帮我啊