|
阅读：2273回复：3
请教ZR36060的寄存器配置
各位老师:
大家好! 上次我发的一个关于咨询OV7620和ZR36060的匹配接口的贴子,现在已经解决了,在此衷心感谢大侠孙江波和guo263的鼎力相助. 现在开发中又遇到这样一个问题,就是数据传回来后,将其转存为JPEG文件,格式都正确,但看到的图像却是五彩斑斓,根本看不出拍摄景物,我怀疑是JPEG的寄存器配置的问题,请教各位老师,我想进行静态图像采集,对存储容量要求不严格,以下寄存器应该如何配置: 1. 0x003(Codec Mode Register) 2. 0x005(Maximum Block Code Volume Register) 3. 0x009~0x00C (Target Net Code Volume Register) 4. 0x00D~0x010 (Target Data Code Volume Register) 5. 0x011~0x012 (Scale Factor Register) 6. 0x013~0x015 (Allocation Factor Register) 7. DRI段、DQT段和DHT段能否完全按照Datasheet上的推荐参数 8. APP段和COM段是否可以不要,也不用在寄存器的0x380~0x3FF中进行初始化. 有哪位老师能百忙之中抽空帮我一把，万分感激！ |
|
|
沙发#
发布于：2005-07-18 09:56
不知楼主是否弄清楚以上问题,小弟也碰到了同样问题
|
|
|
板凳#
发布于：2005-07-19 10:17
/* ZR36060 register addresses */
#define ZR060_LOAD 0x000 #define ZR060_CFSR 0x001 #define ZR060_CIR 0x002 #define ZR060_CMR 0x003 #define ZR060_MBZ 0x004 #define ZR060_MBCVR 0x005 #define ZR060_MER 0x006 #define ZR060_IMR 0x007 #define ZR060_ISR 0x008 #define ZR060_TCV_NET_HI 0x009 #define ZR060_TCV_NET_MH 0x00a #define ZR060_TCV_NET_ML 0x00b #define ZR060_TCV_NET_LO 0x00c #define ZR060_TCV_DATA_HI 0x00d #define ZR060_TCV_DATA_MH 0x00e #define ZR060_TCV_DATA_ML 0x00f #define ZR060_TCV_DATA_LO 0x010 #define ZR060_SF_HI 0x011 #define ZR060_SF_LO 0x012 #define ZR060_AF_HI 0x013 #define ZR060_AF_M 0x014 #define ZR060_AF_LO 0x015 #define ZR060_ACV_HI 0x016 #define ZR060_ACV_MH 0x017 #define ZR060_ACV_ML 0x018 #define ZR060_ACV_LO 0x019 #define ZR060_ACT_HI 0x01a #define ZR060_ACT_MH 0x01b #define ZR060_ACT_ML 0x01c #define ZR060_ACT_LO 0x01d #define ZR060_ACV_TRUN_HI 0x01e #define ZR060_ACV_TRUN_MH 0x01f #define ZR060_ACV_TRUN_ML 0x020 #define ZR060_ACV_TRUN_LO 0x021 #define ZR060_IDR_DEV 0x022 #define ZR060_IDR_REV 0x023 #define ZR060_TCR_HI 0x024 #define ZR060_TCR_LO 0x025 #define ZR060_VCR 0x030 #define ZR060_VPR 0x031 #define ZR060_SR 0x032 #define ZR060_BCR_Y 0x033 #define ZR060_BCR_U 0x034 #define ZR060_BCR_V 0x035 #define ZR060_SGR_VTOTAL_HI 0x036 #define ZR060_SGR_VTOTAL_LO 0x037 #define ZR060_SGR_HTOTAL_HI 0x038 #define ZR060_SGR_HTOTAL_LO 0x039 #define ZR060_SGR_VSYNC 0x03a #define ZR060_SGR_HSYNC 0x03b #define ZR060_SGR_BVSTART 0x03c #define ZR060_SGR_BHSTART 0x03d #define ZR060_SGR_BVEND_HI 0x03e #define ZR060_SGR_BVEND_LO 0x03f #define ZR060_SGR_BHEND_HI 0x040 #define ZR060_SGR_BHEND_LO 0x041 #define ZR060_AAR_VSTART_HI 0x042 #define ZR060_AAR_VSTART_LO 0x043 #define ZR060_AAR_VEND_HI 0x044 #define ZR060_AAR_VEND_LO 0x045 #define ZR060_AAR_HSTART_HI 0x046 #define ZR060_AAR_HSTART_LO 0x047 #define ZR060_AAR_HEND_HI 0x048 #define ZR060_AAR_HEND_LO 0x049 #define ZR060_SWR_VSTART_HI 0x04a #define ZR060_SWR_VSTART_LO 0x04b #define ZR060_SWR_VEND_HI 0x04c #define ZR060_SWR_VEND_LO 0x04d #define ZR060_SWR_HSTART_HI 0x04e #define ZR060_SWR_HSTART_LO 0x04f #define ZR060_SWR_HEND_HI 0x050 #define ZR060_SWR_HEND_LO 0x051 #define ZR060_SOF_IDX 0x060 #define ZR060_SOS_IDX 0x07a #define ZR060_DRI_IDX 0x0c0 #define ZR060_DQT_IDX 0x0cc #define ZR060_DHT_IDX 0x1d4 #define ZR060_APP_IDX 0x380 #define ZR060_COM_IDX 0x3c0 /* ZR36060 LOAD register bits */ #define ZR060_LOAD_Load (1 << 7) #define ZR060_LOAD_SyncRst (1 << 0) /* ZR36060 Code FIFO Status register bits */ #define ZR060_CFSR_Busy (1 << 7) #define ZR060_CFSR_CBusy (1 << 2) #define ZR060_CFSR_CFIFO (3 << 0) /* ZR36060 Code Interface register */ #define ZR060_CIR_Code16 (1 << 7) #define ZR060_CIR_Endian (1 << 6) #define ZR060_CIR_CFIS (1 << 2) #define ZR060_CIR_CodeMstr (1 << 0) /* ZR36060 Codec Mode register */ #define ZR060_CMR_Comp (1 << 7) #define ZR060_CMR_ATP (1 << 6) #define ZR060_CMR_Pass2 (1 << 5) #define ZR060_CMR_TLM (1 << 4) #define ZR060_CMR_BRB (1 << 2) #define ZR060_CMR_FSF (1 << 1) /* ZR36060 Markers Enable register */ #define ZR060_MER_App (1 << 7) #define ZR060_MER_Com (1 << 6) #define ZR060_MER_DRI (1 << 5) #define ZR060_MER_DQT (1 << 4) #define ZR060_MER_DHT (1 << 3) /* ZR36060 Interrupt Mask register */ #define ZR060_IMR_EOAV (1 << 3) #define ZR060_IMR_EOI (1 << 2) #define ZR060_IMR_End (1 << 1) #define ZR060_IMR_DataErr (1 << 0) /* ZR36060 Interrupt Status register */ #define ZR060_ISR_ProCnt (3 << 6) #define ZR060_ISR_EOAV (1 << 3) #define ZR060_ISR_EOI (1 << 2) #define ZR060_ISR_End (1 << 1) #define ZR060_ISR_DataErr (1 << 0) /* ZR36060 Video Control register */ #define ZR060_VCR_Video8 (1 << 7) #define ZR060_VCR_Range (1 << 6) #define ZR060_VCR_FIDet (1 << 3) #define ZR060_VCR_FIVedge (1 << 2) #define ZR060_VCR_FIExt (1 << 1) #define ZR060_VCR_SyncMstr (1 << 0) /* ZR36060 Video Polarity register */ #define ZR060_VPR_VCLKPol (1 << 7) #define ZR060_VPR_PValPol (1 << 6) #define ZR060_VPR_PoePol (1 << 5) #define ZR060_VPR_SImgPol (1 << 4) #define ZR060_VPR_BLPol (1 << 3) #define ZR060_VPR_FIPol (1 << 2) #define ZR060_VPR_HSPol (1 << 1) #define ZR060_VPR_VSPol (1 << 0) /* ZR36060 Scaling register */ #define ZR060_SR_VScale (1 << 2) #define ZR060_SR_HScale2 (1 << 0) #define ZR060_SR_HScale4 (2 << 0) |
|
|
地板#
发布于：2012-11-26 20:54
我也是刚刚在用这个ZR36060，参数不知道怎么载入。不知道楼主能否指教一下，我邮箱dlutliujian@163.com
谢谢了。小弟毕设着急中。。。 |
|