哪位大哥帮我看看我68013的firmware啊？

       我只是想把数据传到EP1里，传一个包，接着就传第二个，对数据不做处理。这样都调不通！汗！
    我用console做的测试，只可以传一个包，第二个就过不去了！
    先谢过了！
#pragma NOIV               // Do not generate interrupt vectors
//-----------------------------------------------------------------------------
//   File:      periph.c
//   Contents:   Hooks required to implement USB peripheral function.
//
//   Copyright (c) 1997 AnchorChips, Inc. All rights reserved
//-----------------------------------------------------------------------------
#include "fx2.h"
#include "fx2regs.h"
#include "fx2sdly.h"            // SYNCDELAY macro

extern BOOL   GotSUD;         // Received setup data flag
extern BOOL   Sleep;
extern BOOL   Rwuen;
extern BOOL   Selfpwr;

BYTE   Configuration;      // Current configuration
BYTE   AlternateSetting;   // Alternate settings


//-----------------------------------------------------------------------------
// Task Dispatcher hooks
//   The following hooks are called by the task dispatcher.
//-----------------------------------------------------------------------------

void TD_Init(void)             // Called once at startup
{
  // set the CPU clock to 48MHz
   CPUCS = ((CPUCS & ~bmCLKSPD) | bmCLKSPD1) ;

   // set the slave FIFO interface to 48MHz
   IFCONFIG |= 0x40;

   EP1OUTCFG = 0xA0;

   EP1OUTBC=0x80;
  
}

void TD_Poll(void)             // Called repeatedly while the device is idle
{
}

BOOL TD_Suspend(void)          // Called before the device goes into suspend mode
{
   return(TRUE);
}

BOOL TD_Resume(void)          // Called after the device resumes
{
   return(TRUE);
}

//-----------------------------------------------------------------------------
// Device Request hooks
//   The following hooks are called by the end point 0 device request parser.
//-----------------------------------------------------------------------------

BOOL DR_GetDescriptor(void)
{
   return(TRUE);
}

BOOL DR_SetConfiguration(void)   // Called when a Set Configuration command is received
{
   Configuration = SETUPDAT[2];
   return(TRUE);            // Handled by user code
}

BOOL DR_GetConfiguration(void)   // Called when a Get Configuration command is received
{
   EP0BUF[0] = Configuration;
   EP0BCH = 0;
   EP0BCL = 1;
   return(TRUE);            // Handled by user code
}

BOOL DR_SetInterface(void)       // Called when a Set Interface command is received
{
   AlternateSetting = SETUPDAT[2];
   return(TRUE);            // Handled by user code
}

BOOL DR_GetInterface(void)       // Called when a Set Interface command is received
{
   EP0BUF[0] = AlternateSetting;
   EP0BCH = 0;
   EP0BCL = 1;
   return(TRUE);            // Handled by user code
}

BOOL DR_GetStatus(void)
{
   return(TRUE);
}

BOOL DR_ClearFeature(void)
{
   return(TRUE);
}

BOOL DR_SetFeature(void)
{
   return(TRUE);
}

BOOL DR_VendorCmnd(void)
{
   return(TRUE);
}

//-----------------------------------------------------------------------------
// USB Interrupt Handlers
//   The following functions are called by the USB interrupt jump table.
//-----------------------------------------------------------------------------

// Setup Data Available Interrupt Handler
void ISR_Sudav(void) interrupt 0
{
   GotSUD = TRUE;            // Set flag
   EZUSB_IRQ_CLEAR();
   USBIRQ = bmSUDAV;         // Clear SUDAV IRQ
}

// Setup Token Interrupt Handler
void ISR_Sutok(void) interrupt 0
{
   EZUSB_IRQ_CLEAR();
   USBIRQ = bmSUTOK;         // Clear SUTOK IRQ
}

void ISR_Sof(void) interrupt 0
{
   EZUSB_IRQ_CLEAR();
   USBIRQ = bmSOF;            // Clear SOF IRQ
}

void ISR_Ures(void) interrupt 0
{
   // whenever we get a USB reset, we should revert to full speed mode
   pConfigDscr = pFullSpeedConfigDscr;
   ((CONFIGDSCR xdata *) pConfigDscr)->type = CONFIG_DSCR;
   pOtherConfigDscr = pHighSpeedConfigDscr;
   ((CONFIGDSCR xdata *) pOtherConfigDscr)->type = OTHERSPEED_DSCR;
  
   EZUSB_IRQ_CLEAR();
   USBIRQ = bmURES;         // Clear URES IRQ
}

void ISR_Susp(void) interrupt 0
{
   Sleep = TRUE;
   EZUSB_IRQ_CLEAR();
   USBIRQ = bmSUSP;
}

void ISR_Highspeed(void) interrupt 0
{
   if (EZUSB_HIGHSPEED())
   {
      pConfigDscr = pHighSpeedConfigDscr;
      ((CONFIGDSCR xdata *) pConfigDscr)->type = CONFIG_DSCR;
      pOtherConfigDscr = pFullSpeedConfigDscr;
      ((CONFIGDSCR xdata *) pOtherConfigDscr)->type = OTHERSPEED_DSCR;
   }

   EZUSB_IRQ_CLEAR();
   USBIRQ = bmHSGRANT;
}
void ISR_Ep0ack(void) interrupt 0
{
}
void ISR_Stub(void) interrupt 0
{
}
void ISR_Ep0in(void) interrupt 0
{
}
void ISR_Ep0out(void) interrupt 0
{
}
void ISR_Ep1in(void) interrupt 0
{
}
void ISR_Ep1out(void) interrupt 0
{
    EP1OUTBC=0x80;                  // re(arm) EP1OUT
    
    EZUSB_IRQ_CLEAR();              // Clear URES IRQ
    EPIRQ=bmEP1OUT;                  
}
void ISR_Ep2inout(void) interrupt 0
{
}
void ISR_Ep4inout(void) interrupt 0
{
}
void ISR_Ep6inout(void) interrupt 0
{
}
void ISR_Ep8inout(void) interrupt 0
{
}
void ISR_Ibn(void) interrupt 0
{
}
void ISR_Ep0pingnak(void) interrupt 0
{
}
void ISR_Ep1pingnak(void) interrupt 0
{
}
void ISR_Ep2pingnak(void) interrupt 0
{
}
void ISR_Ep4pingnak(void) interrupt 0
{
}
void ISR_Ep6pingnak(void) interrupt 0
{
}
void ISR_Ep8pingnak(void) interrupt 0
{
}
void ISR_Errorlimit(void) interrupt 0
{
}
void ISR_Ep2piderror(void) interrupt 0
{
}
void ISR_Ep4piderror(void) interrupt 0
{
}
void ISR_Ep6piderror(void) interrupt 0
{
}
void ISR_Ep8piderror(void) interrupt 0
{
}
void ISR_Ep2pflag(void) interrupt 0
{
}
void ISR_Ep4pflag(void) interrupt 0
{
}
void ISR_Ep6pflag(void) interrupt 0
{
}
void ISR_Ep8pflag(void) interrupt 0
{
}
void ISR_Ep2eflag(void) interrupt 0
{
}
void ISR_Ep4eflag(void) interrupt 0
{
}
void ISR_Ep6eflag(void) interrupt 0
{
}
void ISR_Ep8eflag(void) interrupt 0
{
}
void ISR_Ep2fflag(void) interrupt 0
{
}
void ISR_Ep4fflag(void) interrupt 0
{
}
void ISR_Ep6fflag(void) interrupt 0
{
}
void ISR_Ep8fflag(void) interrupt 0
{
}
void ISR_GpifComplete(void) interrupt 0
{
}
void ISR_GpifWaveform(void) interrupt 0
{
}

原来firmware 不给开这个中断的，晕！大意了！
问题解决了！
Thank you all the same ！